ANSI AD500P1:2015 pdf free download
ANSI AD500P1:2015 pdf free download.Agricultural tractors — Rear-mounted power take-off types 1, 2, 3 and 4 — Part 1: General specifications, safety requirements, dimensions for master shield and clearance zone. These materials are subject to copyright claims of ISO and ASABE. No part of this publication may be reproduced in any form, including an electronic retrieval system, without the prior...
ANSI/OPEI B71.9-2016 pdf free download
ANSI/OPEI B71.9-2016 pdf free download.for Multipurpose Off-Highway Utility Vehicles. 3. Interpretations, Terms, and Definitions 3.1 Mandatory and Advisory Rules. To carry out the provisions of this document, the word shall is to be understood as mandatory and the word should is to be understood as recommended. 3.2 Terms. For purposes of this document， the word Vehicle shall mean Multipurpose Off-Highway...
ANSI/BICSI 006-2015 pdf free download
ANSI/BICSI 006-2015 pdf free download.Distributed Antenna System (DAS) Design and Implementation Best Practices. 1.1.1 Trends Affecting DAS 1.1.1.1 Building Design and Construction Since the 1990s, there has been an increasing focus of integrating sustainable practices into building design and construction. Defined within Leadership in Energy and Environmental Design (LEED), Energy Star ® , and other programs are requirements and recommendations...
ANSI C63.7-2015 pdf free download
ANSI C63.7-2015 pdf free download.American National Standard Guide for Construction of Test Sites for Performing Radiated Emission Measurements. ANSI C63.5, American National Standard for Electromagnetic Compatibility—Radiated Emission Measurements in Electromagnetic Interference (EMI) Control—Calibration of Antennas (9 kHz to 40 GHz). ANSI C63.14, American National Standard Dictionary of Electromagnetic Compatibility (EMC) including Electromagnetic Environmental Effects (E3). CISPR 16-1-4 Edition 3.1 with...
ANSI C78.379-2015 pdf free download
ANSI C78.379-2015 pdf free download.Electric Lamps — Classification of the Beam Patterns of Reflector Lamps. 1 Scope, Purpose, and Application 1.1 SCOPE This standard describes a system for classification of beam patterns and beam angles of reflector lamps. Also a method of describing light output is defined. Reflector lamps are considered to be those lamps having a reflective coating applied...
ANSI/FCI 13-1-2016 pdf free download
ANSI/FCI 13-1-2016 pdf free download.AMERICAN NATIONAL STANDARD DETERMINING CONDENSATE LOADS TO SIZE STEAM TRAPS. 1. PURPOSE The purpose of this standard is to help estimate condensate loads using generally accepted formulas. The result is then used to size a steam trap with sufficient safety factor to discharge the necessary flow throughout the positive pressure differential range without being grossly oversized....
ANSI/FCI 15-1-2015 pdf free download
ANSI/FCI 15-1-2015 pdf free download.AMERICAN NATIONAL STANDARD STANDARD FOR PRODUCTION TESTING OF PRESSURE REGULATORS. 1. PURPOSE This standard establishes minimum guidelines for production testing of pressure regulators for use by manufacturers, specifiers, inspectors, and users to ensure testing of atmospheric leak tightness and seat leakage are completed at the factory before shipment. 2. SCOPE and LIMITATIONS 2.1. This standard provides...
ANSI/FCI 70-3-2016 pdf free download
ANSI/FCI 70-3-2016 pdf free download.AMERICAN NATIONAL STANDARD REGULATOR SEAT LEAKAGE. 1. PURPOSE 1.1 This standard establishes a series of seat leakage classes for regulators and defines the production test procedures. 2. SCOPE & LIMITATIONS 2.1 This standard applies to pilot operated and direct acting pressure reducing, pressure relieving (back pressure), differential pressure and temperature regulators. 2.2 Selection of a leakage...
ANSI/FCI 99-2-2015 pdf free download
ANSI/FCI 99-2-2015 pdf free download.AMERICAN NATIONAL STANDARD PRESSURE REDUCING REGULATOR CAPACITY. 4.1 Suggested test set up and equipment is shown in Figure 1. Assure that all equipment has flow and pressure ratings equal to or greater than that expected in the test. Test set up can be per ISA 75.02.01 and ANSI B109.4. Accuracy of Instruments is also covered in...
ANSI/HI 9.6.7-2015 pdf free download
ANSI/HI 9.6.7-2015 pdf free download.Rotodynamic Pumps – Guideline for Effects of Liquid Viscosity on Performance. 9.6.7.3.2 Methods for determining correction factors Correction factors can be either defined empirically from a data bank containing measurements on various pumps with water and liquids of different viscosities or from a physical model based on the analysis of the energy losses in the pump....